LASER TREE Laser Engraving Module, 10000mW(10W) Output Module with Air Assist System, Built-in FAC, Compressed Spot CNC Carving DIY Laser Master for Laser Cutter Engraving Machine Class 4, 12V

This doubled the laser power of my AtomStack A5 Pro. Lasertree provided instructions for installation and use. They also provided focusing shims in 3, 4 and 5 mm so the laser can be focused based on material thickness and operation (cut vs engrave).The installation was a breeze, though I did have to remove my z axis adjuster. Everything else was a straight bolt-up. I did place the driver board atop the x axis carriage using double sided foam tape,

I bought this laser to upgrade my Nasum A5 Pro, whose puny 5W laser required two passes to cut 3mm basswood.The box contains the laser unit itself, a sliding mounting plate in two parts (one attaches to the carriage, the other to the laser head, a few screws with matching hex wrenches, a power adapter board with cable, a few acrylic focus spacers, and a replacement lens.Attaching the mounting plate to the Nasum carriage would not have been possible without reusing two screws from the previous mounting plate; as it is I could have used two more. I would have appreciated finding the corresponding screws in the box. Two thumbscrews secure the laser plate to the carriage holder and allow for easy focus adjustment, this is very handy.There are two versions of the laser head on this page, 12V and 24V. They look identical, apparently the 24V version see a lot of returns, probably because most controllers on inexpensive engraving tables feed 12V to the laser head. The included voltage adapter can be used to convert 12V into 24 or vice versa if needed, of course at the expense of another board and more wires -- so make sure you check the voltage and pinout on your controller before ordering. The Nasum A5 Pro uses the same connector and 12V, so it was an easy replacement and I don't need to use the adapter board (I could have done with a cheaper version WITHOUT the board, and maybe with a couple more screws instead!)The hose of my air assist pump connected easily to to the brass nozzle and it works great.Finally, the optical protection attaches magnetically to the bottom of the unit. Overall, install took roughly 15 minutes, easy peasy.I ran a few tests and it essentially cuts twice as fast as the original 5W laser: card stock cuts at 2000mm/minute at 50% (instead of 1000mm/m at 50% with the 5W) and the edges are perfect; basswood cuts in a single pass at 200mm/m at 100% instead of requiring two passes at the same speed with the 5W. So, a very worthy upgrade I'm very pleased with.

{UPDATE AT BOTTOM} No adapter plate, no power plug even though it requires one, and the data line is way too short to actually work on even a desktop sized cnc. I want to get some help with this order but Amazon seems to just want me to request a refund or replacement and finding a button to contact seller like a needle in the haystack in 2023.{UPDATE} : customer support was very responsive and willing to provide guidance and assist with sending the mounting bracket and additional wiring. Props for being quick and willing to help! However, Please be aware that the stock mounting bracket does not work stock if you have a foxalien 4040-XE. I had to make a mounting plate out of aluminum to attach to, but it is quite worth it as the mounting plate allows for manual adjustment to further fine tune your z axis control.I also needed to get an additional cable to work with the required length to run between the cnc control box and the adapter, as well as purchase a 24v adapter before everything was functional. After all that was in place it works pretty well though. I have yet to try some major power cuts but it seems to handle some initial cardboard jobs pretty well.

Excelente producto!

Works okay definitely now a 80wMaybe 20-30W

Producto en perfecto estado. Fácil de instalar, LO RECOMIENDO.

but this thing packs a punch. my old glass engravings would take sometimes 4-6 hours. i now do them in 2.5 hours. it improved the time that much. i went from running at 2000mm to 6500mm that much improvement and quality is amazing.

First off, I'll say this has been an incredible upgrade from my old 5.5w diode. It's easily 4x faster than before as well as being able to actually cut through 3mm wood in one pass.That being said... be careful not too long away for long if you're using the magnetic eye shield. I did, and almost paid big time even sitting 5 feet away. A piece that cut out was sticking up and caught the eye shield, partially knocking it off. It somehow wedged between the laser module and the work piece. I noticed a burning smell and looked over to see a nice little fire going. The eye shield was destroyed along with the work piece, thankfully that was all.That said, I definitely recommend this for your next upgrade. Just be safe, and aware.