Pioneer Decorative PVC Slim Line Cover Kit for Mini Split Air Conditioners and Heat Pumps

Bought this based on other reviews to cover the installation of a Mitsubishi ductless heat pump for a bedroom. The delivery was prompt and there were plenty of parts to install a long down drop of the electrical, mechanical and water drain lines (using PVC) parts. Two halves have interlocking grooves. Install the back side to the wall and lay in the lines, then snap on the cover and screw on the connectors at the joints. Literally these things snap together and they hold well. When cutting to length , I used tin snips, but any its a relatively soft plastic and cut easily. I ordered the unit on line and hired a contractor to put the unit in, but I did the line cover kit myself as he ran the lines. The end result is very professional and clean looking. There were extra parts for a couple of 90 degree turns and additional runs an connectors. The contractor was so impressed with this product he said he'll use them for his next install. Its a great product for the money that will protect the installation from the sun and weather and make it look better too. I highly recommend this product. This is not a paid or other wise solicited review.

Perfect for protecting my mini split coolant lines. I didn't realize the flex portion is NOT installable AFTER you attach and pressurize the lines, it must be installed BEFORE because you have to slide them onto the piping. I solved that by using a razor blade to split it down the inside, because these didn't arrive until after I had done the installation. End result looks fantastic.My kit came with four 4-foot lengths of line cover, the flex line, two right angle corners, four couplings, and a "head" cover for the part where the line comes out of the house and starts down the side.Mini split coolant lines are somewhat rigid, so it's better to install these covers before the lines are in place. The head piece and couplings all have holes in the back to screw through and attach to the siding, and the lengths of line cover sort of click into those couplings and are held in place by the couplings.I was able to protect two sets of lines, one for the first floor and one for the second, with two line sets. Very very satisfied with my purchase!

I used this on my Pioneer 18kbtu mini split, and this is too tight for me to recommend for it. I had to use multiple clamps to get it to snap together - so I would recommend not using this for 18kbtu units. Overall, the quality is nice, though, and I was able to make it work.

This installed without too much trouble - its flexible enough to do what you need and stuff the contents in to it - but know that its not super easy - it takes some effort to weave it around and make it all nest down in there just right. The pay off is worth it in the end. I had to modify some pieces and it wasn't quite enough to route all of my 16' of lineset. that is OK as the last 1.5' was just wrapped with plastic wrap stuff. I ended up painting the whole deal when I painted the house and it looked good. I'm installing another one at my Dad's house next year likely and would buy again. will need to buy two kits for a longer line run. this is only good for about 15-16' run.

Great trim cover

Great product

Installed them three years ago. No major complaints during installation, aside from them being a bit tight. Another half inch larger and it would have been an easier install.However after three years in the California sun, they've discolored - the couplers are all very yellow and brittle, but the main sleeves are OK. I might try painting them before scrapping them, but disappointing that they lasted such a short time.

I don't think I have ever seen mini split pipes exposed and there's a good reason for that: It looks ugly, unfinished and unprofessional. This kit is the perfect solution. I have to say it was just barely large enough to accommodate the pipes from my MrCool unit but I miraculously managed to squeeze them in. Since I received this kit after I had already installed the unit, I needed to cut open the corner piece that hides the transition of the pipes into the wall but since it's on the underside, I don't see it and don't expect any issues. The rest assembled nicely and I have several pieces left. I'm happy with the purchase because it looks oh so much nicer now!