How do you zero the small inner dial?

The is no zeroing the small dial. There should be strain on the gauge, with the small indicator reading above zero, then set the dial to zero - then the gauge is zeroed to the thickness of the material used for the strain.

What is the purpose of the round 'knob' the clamp? Not the handle that tightens the clamp but on the other end of that handle?

While it's a bit difficult to grasp what your asking, I'm assuming you mean the black junction partway along the swing arm (the silver but that extends laterally) If you're assuming the other two knobs manage pitch, yaw, tilt, and extension, you'd be correct. The last junction isn't wrapping the silver rod, however it may appear in the images. It bisects it. that's actually two silver rods, the end of each connect to the junction you're asking after: (| |) ========| |========= This give you a bit of leeway in the arm itself. Some give. Yanno, so the $300 Starrit dial indicator (one inexplicably has chosen to mount on a $20 Wen magnetic arm) isn't mangled by the angle of the dangle if your test setup gets rearrangled. The knob basically extends a threaded rod through the cap and exerts force on the opposite side, making it rigid and increasing the accuracy of your measurements (typically up to a full decimal point 0.01 -> 0.001). ...at least, ostensibly that's how this is supposed to go. Again, though: $20. Wen. Made from the finest Chinesium alloys (the only "steel" this device has ever seen is spelled with an "a" and refers to the originator's patent application. Now, no offense intended here, but by virtue of the fact you didn't know this (not that there's any reason you SHOULD have; I'm not being judgy here, honest), then the level of accuracy this tool is capable of providing will almost certainly satisfy your needs. One you've gotten deep enough into milling/machining to CARE about that kind of delta (for woodworking even this is almost overkill; the dimensional instability of wood due to humidity alone cancels out anything at the tenth range), you'll have run into the issue and the solution organically. If this IS for woodworking, just get the dial indicator and some 123 blocks. Really the only practical application for it there is to ensure your blades are parallel to the miter slot on your table/bandsaw. I suppose you could use it to align a tormek perfectly square too, but if you're running a Tormek, again: you're prolly not LOOKING at these.

For the manufacturer or seller - Why doesn't the needle point straight up when at zero?

It does the dial face is adjustable. I use precision devices constantly and my company has to calibrate them every 6 months and this is one product I've had no issue with

Desertcart Logo

Deliver to Belize

For best experience Get the App

DOWNLOAD THE APP

WE SOURCE ITEMS FROM

UAE
UK
India
USA
Japan
KOREA

Customer Services

About Us

Customer Support

Description

🧲 Lock in precision, unlock your workflow.

BUILT TO LAST BACKED - Durable design with a 2-year warranty and nationwide support for professional peace of mind.
EFFORTLESS ADJUSTMENTS - Quick-release lock knob simultaneously secures or frees all joints for rapid, precise setup.
UNIVERSAL COMPATIBILITY - Fits most dial indicators with 3/8-inch, 6mm, and 8mm mounting holes plus dovetail and v-groove base.
UNMATCHED MAGNETIC GRIP - Over 175 pounds of industrial-strength magnetic force ensures zero wobble on any ferrous surface.
360 PRECISION POSITIONING - Three-arm system pivots, bends, and locks fully for ultimate flexibility and up to 14.5 inches height reach.

The WEN Magnetic Base 10714 delivers industrial-strength magnetic force exceeding 175 pounds, combined with a versatile three-arm system that pivots 360° and extends up to 14.5 inches. Featuring a quick-release lock knob for fast adjustments and universal mounting compatibility, it provides a rock-solid, wobble-free platform for dial indicators. Designed for professionals demanding precision, it’s backed by a 2-year warranty and nationwide service support.

Reviews

S**.

Fits all your indactor needs and more.

First, I already have many magnetic bases for Indicators. As a Union Trades Millwright, these tool gets used daily, doing turbine rotor lifts, pump shaft runout and much more.I have many Starrett bases as well as older Craftsman and others just to name a couple.I wanted another holder that had the fine tune adjustment up at the indicator clamp.This WEN mag base not only fullfilled that requirement, but exceeded my expectation with the many sizes and ways to clamp every indicator I have in my arsenal, but the many ways to adjust the indicator is outstanding.The magnet clamping force is really good. The size of the base is slightly bigger than a Starrett, but on par with many other makes.The mag V-groove is good and also has small flat edges along with another side of the mag base have flat edges for multiple ways of attaching it to different machinery shapes.The only slight downside would be that the on/off switch is sensitive and if slightly bumped could disengage. That is the only thing I could find to complain about.This is a very handy and versatile Magnetic base for all of your various types of indicators with a lot of adjustment that makes my work easier and faster.What a great tool.I will be buying more,Steve

8.09.2025

N**G

Solid and works

Solid when tightened. The magnetic switch won't hold on bad surfaces but held perfectly strong on the flat steel of a brake rotor.

13.08.2025

M**O

base reloj comparador

muy buena calidad

6.06.2025

Y**L

Good features. Very strong magnet.

I bought another Magnetic Base but return it because my dial indicator (3/8 inch team) did not fit. VERY good feature of WEN - it has several different sizes to mount dial indicator. Also, I cannot tell in numbers about magnet holding power but it is really strong.

22.07.2024

G**A

Good quality 👌

Good quality, it's compatible with mitutoyo dial indicator.

27.04.2024

Common Questions

Are the products genuine and authentic?+

Yes, all products are sourced directly from authorized retailers in the US, UK, UAE and India. We maintain strict quality control processes and verify each product before shipping. All items come with applicable manufacturer warranties and are covered by our standard return policy.

How long does delivery take and is it reliable?+

Delivery times vary by destination country, typically ranging from 3-9 business days. Each order is fully trackable through our system. We handle all customs clearance and use reliable courier partners for last-mile delivery. You'll receive regular updates about your order status via email and our app.

What is Desertcart? Is it safe to order from?+

Desertcart is an international e-commerce platform operating since 2014. We securely process thousands of orders globally each day. Every product goes through our quality verification process before delivery, and we provide end-to-end order tracking, 24/7 customer support, and a comprehensive returns policy to ensure a safe shopping experience.

How is product pricing calculated?+

Our prices include the product cost, international shipping, import duties, customs clearance, and local delivery charges. We handle all customs and import procedures, ensuring there are no hidden fees upon delivery. PRO members receive additional benefits including free shipping.

BZ$384

Duties & taxes incl.

Belizestore

Free Returns

30 daysfor PRO membership users

15 dayswithout membership

Secure Transaction

ChatGPT - opens in a new tab Perplexity - opens in a new tab Claude - opens in a new tab Grok - opens in a new tab Google AI - opens in a new tab

Trustpilot

TrustScore 4.5 | 7,300+ reviews

Reema J.

Perfect platform for hard-to-find items. Delivery was prompt.

1 month ago

Meera L.

Smooth transaction and product arrived in perfect condition.

3 weeks ago

View all Trustpilot reviews

Manufacturer	WEN
Part Number	10714
Item Weight	3.01 pounds
Package Dimensions	10.79 x 4.33 x 2.76 inches
Country of Origin	China
Style	Three-Arm Magnetic Base w/ Quick Release
Item Package Quantity	1
Included Components	Magnetic Base for Dial Indicators
Batteries Required?	No

WEN Magnetic Base for Dial Indicators, Three Segment, Industrial Strength with Quick Release (10714)

Description

Specifications

Have a Question? See What Others Asked

Reviews

Common Questions