OC200, Hardware Controller

In short, I had a lot of problems with my TP-Link AEP245 access points before getting this, and now I don't. This is a better alternative to a mesh system if you have ethernet in a few spots in the house. I have a large house and a large number of smart devices. I was having a hard time getting good wireless signal in remote corners of the house and my router kept failing because of too many wifi clients. I thought about getting a mesh system, but since I have ethernet in several spots across my house, I would have used the ethernet backhaul anyway. No need to use a mesh system, which is designed to send info wirelessly from device to device at a slower speed. Instead I decided to do what is done in commercial contexts: just use several access points. I purchased three TP-link AEP 245 access points and set them up in a way that gets coverage all over the house. It worked OK, except I kept having problems with devices that roam, like cell phones. They wouldn't let go of one and go to the other. Or something. They always said they were connected but some of the time no internet would get through. The AEP245 is supposed to work in standalone mode when you do this as long as you set them all up with the same SSID, password, and settings, but on different channels. Unfortunately, I cannot recommend them for that configuration. I decided as a last ditch effort to buy this controller. It advertises the ability to use fast roaming technology to tell certain roaming devices to go from one access point to the other as you walk around. Anyway, it did actually solve my problem. You can now walk all over my house with whatever device you want and it will always work. It never goes down, the speeds are awesome, and it was easy to configure and to maintain. To be honest, I'm not actually sure whether my system is using 802.11(k/r/v) or some other technology. All I know is that I had tons of problems with my wifi before getting this, and now I don't. It's a little hard to explain what this device does and TP-Link doesn't make it obvious. It does take control of all your access points and let you configure them from a central location instead of having to connect to each individually. I don't think of that as a huge deal. It allows you to monitor all the clients on all access points and see which is downloading how much, disconnect them, and do all sorts of other stuff. Actually, besides the monitoring of bandwidth and clients and allowing central configuration, it's hard to identify what this really does that you can't do in standalone mode without any controller. However, I can tell you that the internet experience is 100% better with this controller. I don't really understand why it's necessary or exactly how it works, but I'm really glad I got it. I recommend it to anyone who is using multiple TP-Link access points

This OC200 hardware controller is much more reliable than a PC running the Omada SDN software. And cheaper. We have TP-Link gear for wifi at our small museum, about 2 acres outdoors campus and 2 buildings connected by a bridge. We have about 35 cameras, another 15 IoTs, and 3-4 streaming TVs. Our network has 7 APs, 3 POE switches, other switches, a bridge, and an ER7206 router. We were using the Omada SDN software on a dedicated PC, but Windows updates and reboots made this setup unreliable without frequent attention. So we upgraded to this dedicated OC200 controller, which does not have Windows inside, and now things just work without needing attention. Same familiar (and great!) Omada SDN, just without any hassles.

This device has made a very positive difference in my house. I live in a tall, brick, three story row house in Baltimore and had been eeking by with a wireless router on the first floor and wireless repeaters to spread the wireless coverage to the other floors. It was pretty un workable with devices continually losing the link or vanishing for hours. I ran Cat6 everywhere so we could at least use laptops in the bedrooms and in places on the first floor. IPhones pretty much ground to a halt if you moved around the house. I then read about the advantages of wireless access points and bought three TP Link wall plate “enterprise” Access Points (EAPs). I had to also buy a small switch to extend my Cat6 switch with some power over ethernet (PoE) ports that the EAPs need for their power. I put one EAP on each floor and in this configuration, each floor had a dedicated SSID and a stable strong signal. Our iPhones (a 10 and an 11), however, had to be continually told to reconnect to the SSID of the floor they were on, kind of a pain. I read about the OC200 as a way to remedy this without devoting a laptop to the task. The OC200 “adopts” the wired EAPs and treats them like an antenna array and issues a single SSID (or multiple wireless subnetworks if you like) that can be used all over the house. With fast roaming enabled, I can now go anywhere in the house and my iPhone tracks the strongest signal and never drops off. All the wireless devices in the house (doorbell, cameras, music devices, Alexa) now track the same SSID and use the same WEP codes and all of a sudden, everything seems to be able to discover everything else and talk to it. It even works out into the street in front of the house so I can use it in my parked car. TP-Link’s tech support helped me with this as their product literature is a little meager and assumes you are starting from scratch (and that you have a PhD in electrical engineering). It turns out for example, for the OC200 to successfully adopt the EAPs as wired devices, each EAP has to be reset to its factory state; otherwise they are adoptable manually but only as wireless devices and no single SSID wireless network emerges which is way confusing. (When you set up the EAPs without a central controller, you log into each one of them to set it up.) I also found that resetting the OC200 to trigger its setup wizard actually takes about two minutes before it has had coffee and is ready to play. Firmware versions of everything can also matter and the tech support folks pointed me to literature to confirm that my OC200 was properly configured for the EAPs I owned, thankfully everything was compatible. If you want the fast roaming feature, all your roaming gear has to be 802.11k/v/r compatible. Mine must be as it is all working smoothly.

I was hoping this little device would solve all my problems. I bought into TP-Link Omada in a big way starting in 2023 with 4x access points and this OC200. Prior to that I had two wireless access points in my home and the signal was weak. I figured Omada has received a lot of good feedback, and it's used in hotels and businesses, so why not just take care of my wireless issues once-and-for-all. I was hoping this OC20O Controller could solve problems inherent to just having separate Omada Access Points -- either when roaming to different rooms or having them automatically be able to adjust channels, signal, etc. Not quite the night-and-day solution I expected.. I've turned off more features than I've enabled on this system in an attempt to diagnose it. I don't need anything really fancy, a few SSIDs for 2.4ghz and 5ghz -- and a desire to either have the devices pick up the strongest access point as I move around the house, or at least be able to just manually turn wifi off on my device and turn it back on to have it pick up the nearest access point. I just wanted RELIABILITY and speed. Yet somehow that wasn't in the cards. Devices sometimes want to connect to a far away access point for no particular reason, even if they're 5ft from an access point with a full signal. Or a device gets dropped all of the sudden. It's just been a frustrating experience at times, feeling you're stuck trying to diagnose what's happening by turning things off or not enabling all the fancy bells-and-whistles that are features of the Omada system -- without much for debug logs that would help steer you in the right direction. It's more trial-and-error getting anywhere, whether it's enabling/disabling features, trying other wireless channels, enabling or disabling radios, running less access points, restarting access points, upgrading firmware, etc. The 5ghz is another annoyance. 5ghz wireless sounds great, and it is great -- as long as you have a clear line of sight or aren't trying to pass through too many walls from where the access point is located. That's because of wireless regulations limiting signal strength, a relatively limited number of channels to avoid noise from neighbor's 5ghz routers and that 5ghz frequency has a harder time "going the distance" through objects compared to 2.4ghz. So just know that if you want a solid 5ghz signal around your house, you're going to need multiple access points. After a lot of fiddling -- my wireless is now "fairly reliable" -- and I say that, while knocking on wood, because I know that there are still weird things happening like devices connecting to access points further away, then losing the connection. For the most part the system has been reliable-enough, but I have certainly not used some of the features I thought I might on the OC200 due to issues and also thought the OC200 might help the system have better stability and speed. Some of the OC200 features sound great, but have issues -- for instance a single SSID for both 2.4ghz and 5ghz. Sounds great, but in practice devices will then connect to a weak 2.4ghz signals instead of a strong 5ghz signal, or some older devices won't be able to connect if 5ghz is on the same SSID or they'll randomly connect and disconnect. That's not to say it's Omada's fault if devices are dumb (as many apparently are) and can't figure out they should connect to the strongest signal. It's a problem with some other wireless routers as well because it's "up to the device to decide" when a signal is weak to enough of a degree. In that regard I'm glad the Omada system allows you to separate the 2.4ghz and 5ghz signal, as I'm aware some wireless systems don't allow you to do that. FWIW I hard-wire all my access points. I'm not asking the system to deliver fast wireless over a mesh network. But when it should theoretically be able to deliver 600-800 Mbps and yet I'm getting 200 Mbps down in the same room UNLESS I have my device a few feet from the access point where I can get closer to 400 Mbps. That's disappointing. Considering just the OC200 device itself, yes it's nice having everything controlled under one roof and a decent amount of features are now supported (as they continue pushing firmware upgrades). I've used Access Control Lists that are essentially sent out and managed by the access points since I don't have an Omada Router and that works decent too. So there are things to really like about the OC200. Yet there are a lot of features that sound great, that I've just had to turn off or not use because older devices had issues. Also the fact that depending on devices (phones, tablets, laptops) to correctly pick a strong wireless signal or the nearest access point is apparently a foolish thought as some just seem to arbitrarily pick any access point regardless of distance. And sure, you can set a cut-off on the OC200 for when to drop a client with a weak signal, but that can cause some issues of its own. Despite all of this, looking at other wireless systems, it seems other systems can also have these issues, so I have yet to attempt spending another $500-1000 to end up in a similar place. Maybe when Wifi7 gets cheaper.. I would rate the Omada system itself 3.5 stars at this point because it has been OKAY, but hasn't solved all my wireless problems or been as stable or fast as I'd like it, and has taken far longer than I expected to try to work some of the kinks out. The OC200 though, I'll rate 4 stars, simply because it makes it easier to manage all the access points under one roof and get some insight into what's happening on the system as a whole.

TP-Link Hardware Controller (OC200) – Omada SDN Integrated Network Controller This is the brain of my entire TP-Link Omada network. While my setup is technically a home system, it’s built more like something you would normally see in a small commercial environment. The OC200 handles everything without breaking a sweat. My network currently includes multiple components including six Omada access points, a bridge, and several switches all managed through this controller. The OC200 keeps the entire system organized and easy to manage through the Omada interface. Once everything is configured, the controller makes it very simple to monitor the network, manage devices, and make adjustments when needed. Having a centralized management system for the entire network is a huge advantage compared to trying to manage each device individually. Performance has been excellent. Even with multiple access points and network devices connected, the controller runs smoothly and has remained stable. If you’re building an Omada-based network—whether for a large home or small business—the OC200 is really the piece that ties the entire system together. Overall it has been reliable, easy to manage, and a key part of keeping the network running smoothly.

I thought I can run my w APs without one of these and you can. You just miss out on a lot of features. You can also schedule AP reboot daily to clean out some memory every morning from my 100s of light switches and light bulbs.

I bought this device to replace a competitors product and the performance, reliability and configuration options are so much better. I use this primarily to manage my home WiFi network and I am much happier with this product than the previous system I was using. I also like the fact that I can issue guest vouchers to visitors on my “guest SSID” that expire at a specified time, this ensures that permanent access is not required ensuring network security. The previous product I was using was prone to WiFi authentication failures after about 24 hours of uptime requiring constant reboots to resolve which I am not experiencing with this unit.

As much as I would love to give this product a detailed review, the fact of the matter is that there isn't much to say about it. If you need to remotely manage a TP-Link Omada network, then you need this, and there isn't really a great alternative to it. If the only Omada network you need to manage is your own, and you have no need to remotely manage it, then you can manage it just fine by setting up a software-based Omada Controller on a computer on your network, and the OC200 Omada Hardware Controller is simply nice to have. And if you aren't managing an Omada network, then the Omada Hardware Controller is of no use to you. The hardware controller is simple enough to set up using the instructions included in the box. It pretty much shares the user interface of the software-based Omada Controller, so it's familiar enough if you've been managing Omada networks for awhile. That user interface isn't the easiest or most intuitive to use, but it's still better than the web-based administration pages of most pro-sumer and enterprise network components, and certainly better than having to work with a bunch of disparate ones. It's not as if there's an alternative way to manage an Omada network. Well, I suppose you could manage one with a combination of direct web administrators for your routers and switches and SSH command line interfaces for the wireless access points, but while that might open up a handful of features and configuration options that you probably wouldn't miss, it certainly wouldn't make for easier network administration. The only real alternative you would have would be to choose a software-defined network system from another manufacturer, and as of today, 4/16/2024, the only real alternative is Ubiquiti UniFi, which is more refined than TP-Link Omada, but also more expensive, more complex and, in my experience, harder to procure due to Ubiquiti's apparent inability to keep up with demand. All other alternatives I know of are either much cheaper and simpler but also missing key components and features, or much more robust but also many times more expensive than either Omada or UniFi, as well as far more complicated to design, purchase and administer.

I've only used this foress than a week but so far it's been pretty solid. Had a couple issues first time connecting my omada router and switch which kept not joining But after a bit of resetting and connecting I finally got it all paired and it's been solid since. Nice to have one panel to control all my omada gear and nice to have easy to read useful info taken from all gear in and placed in one spot.

The Omada software needs to be on 24x7 for certain features to work. eg: portal authorisation, AP roaming. The challenge with PC based systems is that when PCs reboot, the software javascript can't start up easily. Furthermore the cost a PC is more than the Omada hw controller and will take up more space. Worth investing in this hardware appliance.

هذا الجهاز يسهل عملية الاعدات للاجهزة المتعددة من مجموعة "ؤمادا" بحيث لا تلجأ لعمل الاعدادت لكل جهاز على حدى ويجعل الاجهزة متوافقة مع بعض

El controlador es muy fácil de configurar y muy recomendable tenerlo en el sistema, se alimenta por POE y se agradece esa característica

Con le ultime versioni del firmware è diventato davvero un prodotto irrinunciabile per la gestione di quasi tutti i device TP-Link. Consente una gestione facilissima di reti anche molto complesse e con configurazioni non comuni. Ottima la dashboard e il sistema di monitoraggio.